HomeMy WebLinkAboutRFP 19-10 APPENDIX A - Sebastian Design Intent DocumentDesign Intent Document
23 August 2019
City of Sebastian Destination Guide
Table ofContent
General Specifications 3
9
13
18
37
42
Graphic Standards
Sign Palette
Sign Details
Fisherman’s Landing Sign Details
Sign Placement Recommendations
Gateways 14
19
21
23
25
27
2931
38
40
33
34
151617
Inside CRA
Outside CRA
Fisherman’s Landing Signs
City of Sebastian Gateway
Gateway Sign
Gateway with Marquee
Large Vehicular Directional Sign
Small Vehicular Directional Sign
Parking Directional Sign
Pedestrian Kiosk
Gateway
Fund Acknowledgement Sign
Sign Maintenance and Longevity
Construction Details
General Specifications
4City of Sebastian Destination Guide General Specifications 08/16/2019
PART 1 - GENERAL SPECIFICATIONS
1.1 SUMMARY
A.This Section includes engineering, furnishing, and installing the folow
ing signage and support systems:
1. Aluminum signs and supports.
2. Wayfinding signs, directories & room identification signs.
3. Dimensional characters and icons.
4. Sponsorship & branding signage.
B. Sign & display locations are indicated on the Sign Location plans. Sign
& display details are indicated in the Signage Detail Manual. Both are
under separate cover.
1.2 PERFORMANCE REQUIREMENTS
A. Structural Performance: Provide signs and anchorage points capable
of withstanding the effects of gravity, wind, snow, and seismic loads and
stresses, as indicated in the General Notes of the Structural Drawings
determined according to the local building code and authorities having
jurisdiction, reference specification section 01 40 00 Quality for
Engineer.
1. Deflection of signs and supports in vertical and horizontal di-
rection shall be no greater than 1/360 of clear span or .75-inch
(19 mm), whichever is smaller.
B. Thermal Movements: Provide post and panel signs that allow for
thermal movements resulting from the following maximum change
(range) in ambient and surface temperatures by preventing buckling,
opening of joints, overstressing of components, failure of connections,
and other detrimental effects. Base engineering calculation on surface
temperatures of materials due to both solar heat gain and nighttime-sky
heat loss.
1. Temperature Change (Range): 120 deg F (67 deg C), ambient;
180 deg F (100 deg C), material surfaces.
1.3 SUBMITTALS
A. Product Data: Submit manufacturer’s technical data and installation
instructions relative to materials, dimensions of individual components,
profiles, and finishes for each type of material required.
B. Shop Drawings: Submit shop drawings for fabrication and installa
tion/mounting method for each typical sign type, or display type. In-
clude plans, elevations, Iso views and large scale details of each
element. Include large scale sections of typical members and other
components. Show fabrication joints, seams, grain direction and fasten-
ers. Show anchors, grounds, reinforcement, accessories, layout, and
installation details.
1. For items required to comply with design loads, include struc
tural analysis data signed and sealed by the licensed profession-
al engineer responsible for their preparation.
2. Submit graphic layouts for verification, including outline of
sign face, character spacing, line spacing, and copy composition.
3. Engineering, document & sample review, fabrication, and con-
struction schedule.
4. For signs supported by or anchored to permanent construc
tion, provide setting drawings, full-size spacing templates, and
directions for installation of anchor bolts and other appropriate
anchors to be installed.
5. Submit drawings in 11-inch by 17-inch format unless otherwise
requested by the Designer.
6. Provide a proof of all final artwork.
C. Samples: Submit three 6-inch (150 mm) square samples of each
material showing finishes, colors, surface textures and qualities of man-
ufacturer and design of each component including graphics. One sam-
ple set to be kept by Designer, contractor, and client as a record to later
match against items in the field. Only finishes new to Phase 5 will be
required for submittals.
1. Submit full-size sample first article units, per Section 3.6, be-
fore production run is commenced. Acceptable units may be
installed as part of the work.
D. Maintenance Data: Provide a Maintenance and Operating Manual
comprised of cleaning and operations needs for each sign/graphic/
display type. This shall include information on repair due to common
vandalism, changing of messages and parts replacement needs. Include
manufacturers’ brochures and parts lists describing the actual materials
used in the work, including metal alloys, finishes, electrical components
and other major components. Provide working art file templates to the
owner for future use.
1.4 QUALITY ASSURANCE
A.Professional Engineer Qualifications: A professional engineer who is
legally qualified to practice in jurisdiction where Project is located and
who is experienced in providing engineering services of the kind indicat-
ed. Engineering services are defined as those performed for design and
installations of signs, and miscellaneous supports that are similar to
those indicated for this Project in material, design, and extent.
B. Manufacturer Qualifications: All fabrication within this section shall
be performed by a manufacturer with a minimum of five (5) years expe-
rience producing and installing Designerural signs, and a minimum
of five (5) years experience producing compliant signs as specified in
ANSI 117.1 (1986), Minimum Guidelines and Requirements for Acces-
sible Design (MGRAD), Uniform Federal Accessibility Standards (UFAS)
and Americans with Disabilities Act Accessibility Guidelines (ADAAG).
C. Drawings and Specifications: The Designer will provide electronic
files of typical sign layout drawings in Adobe Illustrator CC format. For
electronic files requested in any format other than Adobe Illustrator CC,
the Contractor shall reimburse the Owner, for additional services re-
quired of the Designer for converting the electronic files. Designer will
provide electronic files indicating fonts, icons, designs, and key visual
parameters of the design intent. Fabricator shall develop and produce
final, high resolution production-ready artwork based on these guides
and the details on the Drawings – this includes any up-sampling or inter-
polation required for large scale photo based graphics.
1. Drawings and specifications indicate spacing of members,
sizes of components, profile, dimensions, materials, and design,
assembly and fabrication requirements for the signs.
2. Requests for deviations from indicated dimensions and pro-
files will be considered provided that the intended aesthetic
effect is not modified, as judged and approved solely by Design-
er. If modifications are proposed, submit comprehensive explan-
atory data to Designer for review.
D. Uniformity of Manufacturer: For each separate type of material, finish
or sign or display type, obtain signs from a single manufacturer to en-
sure consistency.
1. Manufacturer’s name, trade name, or trade mark shall not ap-
pear on any visible surface.
E. Adhesion Testing – For all applied graphic films and vinyl products,
perform adhesion tests on accordance with manufacturer’s specifi-
cations. Provide results of adhesion testing to the Designer and the con-
tractor for approval.
F. Fire-Test-Response Characteristics: Provide banners and flags con-
structed of fabrics that are identical to products that pass Test Method 1
of NFPA 701 performed by UL or another testing and inspecting agency
acceptable to authorities having jurisdiction.
1. Flame-Spread Index: 25 or less.
2. Smoke-Developed Index: 450 or less.
G. Welding Standards: Qualify procedures and personnel according to
the following:
1. AWS D1.1, “Structural Welding Code--Steel.”
2. AWS D1.2, “Structural Welding Code--Aluminum.”
3. AWS D1.3, “Structural Welding Code--Sheet Steel.”
4. AWS D1.6, “Structural Welding Code--Stainless Steel.”
H. Aesthetic Requirements: Provide copy with straight and true edges;
space characters with tracking and leading as indicated; reproduce type
faces accurately with square corners and even curves; provide uniform
letters and symbols; and provide smooth finishes with no visible imper-
fections.
I. Regulatory Requirements – Comply with applicable requirements of
the applicable laws and authorities. Obtain necessary approvals and
permits from all such authorities as required.
J. ADA Accessibility Guidelines: All signage shall comply with the ADA
Accessibility Guidelines where applicable. Characters and graphics,
including but not limited to, copy height, letter stroke, symbols, materi-
als, and finishes indicated on the Drawings are intended as guidelines
for compliance. Implement each applicable ADA Guideline. Should con
flicts arise, notify the Designer before proceeding.
5City of Sebastian Destination Guide General Specifications 08/16/2019
K. Mockups: Provide one mockup sign of each type indicated in the
schedule at the end of this Section, to verify selections made under
sample submittals and to demonstrate aesthetic effects and set quality
standards for materials and fabrication.
1. Approved mockups may be forwarded to the Project site and
may become part of the completed Work.
L. Electrical Components, Devices, and Accessories: Listed and labeled
as defined in NFPA 70, Article 100, by a testing agency acceptable to
authorities having jurisdiction, and marked for intended use.
1.5 PROJECT CONDITIONS
A. Field Measurements: Verify dimensions of install locations for all
items by field measurement before fabrication and indicate measure-
ments, and any obstructions on Shop Drawings.
1. Wall Graphic Dimensions. Field verify dimensions and provide
digital templates to the Designer for all applied wall graphics.
Note all obstructions (fire strobes, hatches, panels, electrical
boxes, exit signs, columns, etc.), and as-built dimensions. These
templates are to be used in the preparation of all produc-
tion-ready art files. Where required, the artwork is to be modi-
fied to eliminate any conflicts obstructions, or variations in in-
stall size. The Designer is to review and approve all such
necessary changes to the artwork before fabrication.
2. Established Dimensions: Every effort shall be made to verify
dimensions in the field before production. In the case where field
measurements cannot be made without significantly delaying
the Work, the Fabricator is to review the established installation
location and dimensions with the Contractor and the Designer.
The Contractor is responsible to provide an installation surface
that accommodates the established dimensions identified.
1.6 COORDINATION AND SCHEDULE
A. Installation: Coordinate installation with the Contractor. For items
supported by or anchored to permanent construction, coordinate spe-
cific requirements for types and placement of anchorage devices and
similar items to be used for attaching signs and displays.
1. For any items supported by, anchored to or mounted to per-
manent construction, furnish templates to the Contractor for
installation of blocking, anchorage devices, and electrical
conduits.
2. For any wall coverings that require a level 5 finish furnish
templates to the Contractor and coordinate wall preparation in
keeping with the product manufacturers specifications.
B. Prepare a schedule indicating engineering, sample and material re
views, print proofs, fabrication, delivery, installation, and final inspec-
tion of the Work. Submit this schedule to the Designer and Owner for
approval and coordination with other work at the Project Site.
C. Coordinate location of remote transformers with building construc-
tion. Ensure that transformers are accessible after completion of Work.
1.7 DELIVERY, STORAGE AND HANDLING
A. Package material in like groups and label accordingly.
B. Protect items during transit, delivery, handling, and storage to pre-
vent damage, soiling, and deterioration. Minor damage to finishes may
be repaired provided the final finishes are equal to the original finishes,
are without noticeable flaws, and are acceptable to the Designer. If not
in like-new condition, or if not acceptable to the Designer, remove and
replace damaged items with new signs.
C. Coordinate delivery and storage of sign materials with the Contrac-
tor in advance. Schedule delivery to minimize storage requirements. Ma-
terials stored at the Project Site without prior approval may have to be
relocated at the Fabricator’s expense.
1.8 MAINTENANCE
A. Furnish a list of cleaning materials appropriate for maintenance of
signs, graphics and displays to both the Owner and the Contractor. Pro-
vide written instructions for proper maintenance, electrical access, and
character and lighting replacement procedures. Include recommended
methods for removal of residual adhesives from wall surfaces after re-
moval of adhered items.
PART 2 - PRODUCTS
2.1 MATERIALS, GENERAL
A. Use materials of size and thickness indicated or, if not indicated as
required to produce strength and durability in finished product for use
intended. Work to dimensions shown or accepted on shop drawings,
using proven details of fabrication and support. Use type of materials
shown or specified for various components of work.
B. All materials shall be free from defects impairing strength, durabi-
lity, and appearance. No fabrication or installation materials or pro-
cedures shall be used that will in any way change the usual quality or in
any manner have an adverse effect on existing materials and surfaces.
All materials shall be new stock, unless the Designer has specified a
reclaimed or recycled material.
C. Graphic Content and Style: Provide graphic layouts and sign copy that
complies with requirements indicated in the Signage Detail Manual and
Signage Message Schedule and on preliminary artwork supplied by
Designer for size, fonts, style, spacing, content, mounting height and
location, materials, finishes, and colors.
2.2 MATERIALS
A. General: For the fabrication of exposed metal work, use only materi-
als which are smooth and free of surface blemishes including pitting,
roughness, seam marks roller marks, and trade names. Do not use ma-
terials which have stains or discolorations.
1. Provide stretcher leveled standard of flatness.
B. Aluminum Sheet and Plate: ASTM B 209 (ASTM B 209M), alloy and
temper recommended by aluminum producer and finisher for type of
use and finish indicated, and with at least the strength and durability
properties of alloy 5005-H15.
1. Thickness: Provide aluminum sheets and plates in sizes speci-
fied or indicated on the Drawings.
C. Aluminum Extrusions: ASTM B 221 (ASTM B 221M), alloy and tem-
per recommended by aluminum producer and finisher for type of use
and finish indicated, and with at least the strength and durability prop-
erties of alloy 6063-T5.
D. Stainless Steel: Grade and type designated below for each form re-
quired:
1. Tubing: ASTM A 554, Grade MT 316.
2. Pipe: ASTM A 312/A 312M, Grade TP 316.
3. Castings: ASTM A 743/A 743M, Grade CF 8M.
4. Sheet, Strip, Plate, and Flat Bar: ASTM A 666, Type 316.
5. Bars and Shapes: ASTM A 276, Type 316.
E. General: Plastic shall be free of imperfections from forming or fabri-
cation. All surfaces shall be free from scratches and shall be cleaned
and polished per manufacturer’s instructions at completion of installa-
tion. Edges shall be flame polished, free of saw marks and chips, and be
eased, unless otherwise noted.
F. General: Provide vinyl graphic film suitable for interior and exterior
applications of types indicated below.
1. Vinyl Thickness: 2-mil (0.05 mm), minimum.
2. Adhesive: Clear, pressure sensitive, permanent adhesive (un-
less removable adhesive is specified).
3. Overlaminate: Include a Matte overlaminate for all interior
vinyl graphic films unless otherwise indicated in the Signage De-
tail Manual.
4. Installation: Use minimum overlapping seams advised by the
manufacturer.
G. Basis-of-Design Products: The design is based on the products
named. Subject to compliance with requirements, provide either the
named products or comparable product by one of the other specified
manufacturers. Comparable products are subject to review and approv-
al through the submittal process specified. Note: All film/vinyl materials
require an adhesion test prior to printing to confirm successful
adhesion.
1. Opaque Vinyl Film: Non-reflective, pre-spaced die-cut letters
and film, supplied in specified typeface, color, and spacing on a
quick-release backing sheet.
2. Transparent Vinyl Film: 3M Scotchcal™ Clear Graphic Film
8626 ES.
3. Translucent Vinyl Film: 3M Scotchcal™ Translucent Graphic
Film 8628 ES.
6City of Sebastian Destination Guide General Specifications 08/16/2019
4. Opaque Imaging Media for smooth surfaces: 3M Controltac
Graphic Film with Comply v3 Adhesive IJ180CV3-10 with 3M
Scotchcal Matte Overlaminate 8510M
a) Provide alternate pricing for 3M Scotchcal Graphic
Film with Comply Adhesive IJ40C-10R with 3M Scotchcal
Matte Overlaminate 8510M
5. 3M Scotchcal™ for Textured Surfaces; Series IJ8624 with 3M
Luster Overlaminate 8524.
6. 3M Panaflex™ Awning and Sign Facing; Series 945GPS.
7. 3M Vinyl 8150 with 7 Year Lifespan for window graphics.
H. Available Manufacturers: Subject to compliance with requirements,
manufacturers offering products that may be incorporated into the Work
include, but are not limited to, the following:
1. 3M
2. Avery Dennison Graphics Division
3. Orocal/Orofol Graphic Products
2.3 HARDWARE, FASTENERS, AND ADHESIVES
A. Fasteners: Unless otherwise indicated, use concealed fasteners fab-
ricated from metals that are non-corrosive to either the sign material
or the mounting surface. If concealed fasteners are not practical or pos-
sible, provide vandal-resistant fasteners.
B. Fabricate brackets and fittings for bracket-mounted signs from ma-
terials compatible with panel sign construction and mounting conditions
indicated. Factory-paint brackets in color matching background color of
panel sign.
1. Steel Tubing: Cold-formed steel tubing complying with ASTM
A 500, Grade B.
2. Structural Steel Shapes, Plates, and bars: Cold formed steel
fabrications complying with ASTM A36.
C. Anchors and Inserts: Use non-ferrous metal or hot-dipped galva-
nized anchors and inserts for exterior installations and elsewhere as re-
quired for corrosion resistance. Use toothed steel or lead expansion bolt
devices for drilled-in-place anchors. Furnish inserts, as required, to be
set into concrete or masonry work.
1. For attachment to metal panels, use #12 stainless steel, Type
410, self-tapping screws with integral neoprene washers.
D. Adhesives: Provide products equal to “Depend 330” as manufactured
by Loctite Acrylic Adhesives. (216)881-2828. Fabricator shall verify with
painting manufacturer compatibility of the adhesive to the paint.
E. Very High Bond (VHB) Tape: Provide 3M (or approved equal) VHB
tape at the appropriate thickness/strength required for the weight and
size of each item installed.
F. Silicone Adhesive: Provide liquid silicone adhesive (sealant) with a
methanol or acetic cure as recommended by the sign fabricator.
G. VOC Content of Interior Sealants: Sealants and sealant primers used
inside the weatherproofing system shall comply with the following limits
for VOC content when calculated according to 40 CFR 59, Subpart D
(EPA Method 24):
1. Designerural Sealants: 250 g/L.
2. Sealant Primers for Nonporous Substrates: 250 g/L.
3. Sealant Primers for Porous Substrates: 775 g/L.
H. Spacers: Provide Manufacturer’s standard spacers when necessary.
2.4 GRAPHIC REQUIREMENTS, GENERAL
A. General: Type style shall be as indicated in the Signage Detail
Manual.
1. Typeface, numerals, icons and designs shall be consistent to
the design intent shown in the Signage Detail Manual. Some vari-
ation in tracking and character width to ensure messages fit,
may be acceptable. Any variations to be reviewed and approved
by the Designer.
2. Characters indicated on the Drawings are intended as guide
lines for layouts and font size only, and are based on scale calcu-
lations of the message lengths within given and estimated sign
areas. The actual copy required on individual signs is indicated in
the signage message schedule. Should conflicts arise in the final
message layout, notify the Designer before proceeding.
3. Spelling and punctuation shall be correct. Should an error in
spelling or punctuation be found, or the spelling appears ques-
tionable, notify the Designer before proceeding.
4. Align letter forms to maintain a baseline parallel to the sign
format, unless otherwise indicated. Maintain uniform margins in
sign layouts.
5. Suite Identification Signs, and Signs with Name Inserts: Owner
will determine names for each individual suite or office.
6. Provide digital proofs of final signage layouts to the Designer
for approval before fabrication.
B. Production-Ready Artwork: The Signage Detail Manual includes
specifications for all visual elements including, but not limited to, type,
symbols, logos, photography, artwork, and arrows. The Fabricator is to
create final production-ready artwork necessary to complete all signs
and graphics based on the design intent included in the Signage Detail
Manual.
1. Production-ready artwork is to be high enough resolution to
provide crisp edges and lines for all vector artwork, and to avoid
any visible blurring or pixelation of photographic images. Fabri-
cator to interpolate and up-sample photographic artwork as
required for the installation location and viewing distance. Do
not use the construction documents as production art. The Fab-
ricator is to provide printed proofs of all graphics to ensure color
and resolution are acceptable – samples to include a swatch of
the 100% full size graphic as well as a scaled version of the en-
tire art work – printed on the specified substrate.
2. Silkscreens shall be executed from photoscreens or negatives.
Pattern cut screens may be used where non-repeat copy is re-
quired; however, copy mask shall be equivalent to photoscreen
quality. Do not use the construction documents as production
art.
2.5 FABRICATION, GENERAL
A. General: Fabricate signs to comply with requirements indicated on
drawings for materials, thicknesses, finishes, colors, designs, shapes,
sizes, and details of construction.
1. Form exposed faces and sides of signs to produce surfaces free
from warp, distortion, and “oil canning.”
a) Include internal bracing for stability and attachment of
mounting accessories as required.
b) Cut metal edges on a continuous line and sand
smooth. Seams shall be straight and symmetrical.
c) Form exposed connections with hairline joints, flush,
and smooth.
d) Form exposed work true to line and level with sharp
angles, surfaces, and edges. Ease exposed edges to a ra-
dius of approximately .03125-inch (0.8 mm) unless other-
wise indicated. Form bent-metal corners to smallest radi
us possible without causing grain separation or cracking
of applied finishes.
2. Welding, when necessary, shall be of the appropriate type to
minimize permanent distortions of flat surfaces. Remove weld-
ing flux, oxides and discolorations by pickling or grinding,
so that these areas match the finish of the adjacent areas. Re-
pair damage caused by the fabrication by grinding, polishing,
or buffing.
a) Weld corners and seams continuously, complying with
AWS recommendations. At connections, grind exposed
welds smooth and flush to match and blend with adjoin-
ing surfaces.
3. Cut, reinforce, drill, and tap miscellaneous metal work as indi-
cated to receive finish hardware and similar items.
4. Produce smooth, even, level sign panel surfaces, constructed
to remain flat under installed conditions within a tolerance of
plus or minus one percent measured diagonally from corner to
corner.
5. Fabricate, brackets and fittings for signs to suit sign panel
construction and mounting conditions indicated. Connections,
angles, shapes and details shown are suggestive and are to be
sized, reinforced and detailed as required. Details not shown are
to be equal in quality to those detailed. Factory paint brackets
in color matching background color of sign panel.
6. Provide concealed access to internally illuminated signs for
relamping and service. Service access shall be waterproof and
secured against vandalism.
7. Conceal union, fabricator, or other labels.
8. For sign panel units in exterior applications provide standard
7City of Sebastian Destination Guide General Specifications 08/16/2019
weatherproofing construction, including weather-stripping,
weeping, and venting provisions for condensation control.
B. Metal signs facing and cladding shall be aluminum unless otherwise
indicated or specified in the Signage Detail Manual.
C. Where galvanized steel and aluminum meet, the materials shall be
materially isolated from one another to prevent electrolytic action. Alu-
minum joints and connections shall be heli-arc welded and flush, true,
ground, and polished smooth and without defects. Character forms
shall be cut true to typeface with no burns or imperfections of any kind.
D. Internal Structure: Provide completely hidden, internal structures for
support and anchorage, unless indicated otherwise on the drawings.
Primary support structure shall hot dipped galvanized steel or
aluminum.
2.6 PANEL SIGNS
A. Exterior Plaque Sign: Unless otherwise specified in the Signage De-
tail Manual, provide products fabricated from 0.125-inch aluminum
plate with 0.030 inch thick double face tape mounting and silicone ad-
hesive. All exterior signage is to include weep/drain holes as required.
1. Finish: As indicated in the Signage Detail Manual.
2. Graphics: As indicated in the Signage Message Schedule.
B.Chemically-etched Zinc Sign Panels: Unless otherwise specified in the
Signage Detail Manual, sign copy shall be raised 1/32 inch from plaque
first surface. Provide opaque graphics and Braille to comply with ADA
regulations.
1. Thickness: 0.125 inch (3.2 mm).
2. Zinc Finish: Manufacturer’s sandblasted with horizontal grain.
3. Background Texture: Smooth, matte finish.
4. Graphics: As indicated on the Drawings.
5. Manufacturer: Dixie Graphics.
D. Framed Hollow-Box-Type Panels:
1. Panel Material: Unless otherwise specified in the Signage De-
tail Manual, 0.125-inch- (3.2-mm-) thick aluminum sheet.
2. Panel Finish: Unless otherwise specified in the Signage Detail
Manual, baked enamel.
a) Panel Finish: Manufacturer’s standard semigloss finish
with UV inhibitors.
b) Provide clips welded to back of panels for installation
without visible fasteners.
3. Frame Material: Unless otherwise specified in the Signage
Detail Manual, extruded aluminum, fabricated to profile indicat-
ed; comply with the following:
a) Frame Finish: High-performance organic coating.
b) Corner Condition: Corners rounded to radius
indicated.
PART 3 - EXECUTION
3.1 PREPARATION
A. General: Examine area, surfaces and conditions under which the work
is to be installed. Notify the Contractor in writing of conditions detri-
mental to the proper and timely completion of the work. Starting work
implies acceptable surfaces and conditions.
3.2 INSTALLATION
A. General: Locate signs, graphics and displays where shown on Sign
Location Plan, and Signage Detail Manual, attaching to substrates in
accordance with manufacturer’s instructions, unless otherwise
indicated.
1. Install signs level, plumb, and at heights indicated, with sur-
faces free from distortion and other defects in appearance.
B. Surfaces under adhesive applied units shall be smooth, clean, and
free of dust, grease, fingerprints, or other foreign matter. All adhesives
required shall be used in accordance with recommendations made by
the manufacturer of the material to be laminated or adhered. No adhe-
sives that will fade, discolor, or delaminate because of ultraviolet light
or heat shall be used. Adhesives shall not change the color of or dete-
riorate the materials to which they are to be applied. The adhesives shall
be of a non-staining, non-yellowing quality. All visible joints shall be free
from air bubbles and other defects.
C. Within one week of scheduled completion of installation, prepare a
punch list itemizing:
1. Uppercase letters instead of lowercase or vice-versa.
2. Improper alignment of letters on sign panel.
3. Improper alignment of signs.
4. Chipped or scratched finishes.
5. Unpainted exposed fasteners.
6. Fabricator’s label displayed.
7. Improper cleaning of sign surfaces or surrounding wall areas.
8. Damage to surrounding surfaces.
9. Missing signs, graphics, displays.
10. Incorrect install locations.
11. Missing trim, corner guards, or other finishing.
12. Any areas that require touch up paint.
F. Repair or replace damaged units as required after Designer’s final
inspection.
3.3 PATCH AND ADJUST
A. Patch existing surfaces damaged because of work under this section.
Patch with same materials as existing. Fabricator shall paint and harmo-
niously blend and contour all repairs to match adjoining conditions so
that they are not noticeable to view.
B. Touch-up any mars or nicks in painted finishes of all signs and adja-
cent structures. Touch-up shall be the same paint product as used for
this sign finish. Touch up areas should blend with surrounding areas and
not be noticeable to view.
C. Corrosion Protection: Coat concealed surfaces of aluminum that will
be in contact with grout, concrete, masonry, wood, or dissimilar metals
with a heavy coat of bituminous paint.
D. Galvanized Surfaces: Clean field welds, bolted connections, and
abraded areas and repair galvanizing to comply with ASTM A 780,
Annex A2.
3.4 CLEANING AND PROTECTION
A. At completion of installation, clean exposed surfaces in accordance
with the manufacturer’s instructions. All items shall be free of glue, fin
gerprints, dirt, grease, or any other imperfections.
B. Evidence of installation work or damages incurred on other surfaces
shall be cleaned or repaired prior to completion of work. Protect units
from damage until acceptance by Owner.
C. Remove all packing and construction materials from site. Leave
premises clean, ready for work under other contracts or ready for use.
D. Instruct the Owner in writing as to the correct operation and mainte-
nance of all signs and sign components.
E. Demonstrate to the Owner the operation of all access panels, and
replacement of lamps, ballasts, and transformers as applicable.
F. Furnish Owner with a pint of each paint and finish material used on
sign.
3.5 SCHEDULE OF MOCKUPS
A. Provide a mock-up (partial for large items; complete for smaller
items) of each sign/display type requested at the fabrication facility for
review. The requested mock-ups shall be coordinated with Designer.
Mock-ups once approved may be used towards final install count.
B. When accepted, mock-up shall serve as the standard for materials,
workmanship, and appearance for the work throughout the project.
C. Provide work-in-progress sign elements reviews. Scheduled or un
scheduled viewings at the Fabrication Facility may be initiated by the
Owner’s Representative as deemed necessary to ensure continued
quality control and make any adjustments required during fabrication.
Unsatisfactory items are to be corrected by the Fabricator as directed by
the Owner or owner’s representative.
D. Scaled mock up of graphic artwork + Full size print swatch of all
graphic prints
1. All printed applied wall or glass graphics graphics.
8City of Sebastian Destination Guide General Specifications 08/16/2019
3.6 WARRANTY
A. Submit to the Owner’s Representative a 1-year written warranty
(effective the date of final acceptance) covering all signs contractor will
agree to repair or replace defective signs. Upon notification of such
defective signs within the warranty period, make necessary repairs or
replacement at the convenience of the Owner’s Representative.
B. Submit to the Owner’s Representative a 1 year written warranty,
warranting that the factory-applied finishes will not develop excessive
fading or excessive non-uniformity of color or shade, and will not crack,
peel, pit, corrode or otherwise fail because of defects in materials or
workmanship within the following defined limits. Upon notification of
such defects within the warranty period, make necessary repairs or re
placement at the convenience of the owner’s representative.
Graphic Standards
City of Sebastian Destination Guide
City of Sebastian, FL 10DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Graphic StandardsScale: NTS
TYPOGRAPHY &
TYPEFACES
This page provides a reference for the typefaces for
the Waynding Signage System. Typefaces may not
be changed. During fabrication, the height and width
ratio of letter forms must be maintained proportionately.
Vehicular Signage:
Typeface for vehicular signs is Clearview Hwy or Highway Gothic Type D.
Signs placed on roads with a speed limit of over 25MPH shall have 6" high type.
Signs placed on roads with a speed limit of 25MPH and lower shall
have 4" high type. Type may be upper and lower case.
Pedestrian Signage:
Minimum 1" high copy is recommended for pedestrian
directional signs.
Typeface A - Highway Gothic (Vehicular use only)
ABCDEFGHIJKLMNOPQUSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
Typeface B - Caxton Bold
ABCDEFGHIJKLMNOPQUSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
Typeface C - Myanman Text Regular
ABCDEFGHIJKLMNOPQUSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
Typeface D - Myanman Text Bold
ABCDEFGHIJKLMNOPQUSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
1234567890
City of Sebastian Destination Guide
City of Sebastian, FL 11DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Graphic StandardsScale: NTS
COLORS & MATERIALS
Consistent use of a color palette creates a recognizable “system”.
The Color Palette found on the following pages provides a
reference for specifying a paint color or material.
The Fabricator is required to submit painted color chips
and material samples for approval prior to sign fabrication.
The ADA requires a minimum of 70% contrast between
text and background for the legibility.
Surface applied, exterior sign paint and protec-
tive top coat: Acrylic Polyurethane w/ UV
inhibitor, nished with Clear Coat Satin nish.
Surface applied, exterior sign paint and protec-
tive top coat: Acrylic Polyurethane w/ UV
inhibitor, nished with Clear Coat Satin nish.
Surface applied, exterior sign paint and protec-
tive top coat: Acrylic Polyurethane w/ UV
inhibitor, nished with Clear Coat Satin nish.
Surface applied, exterior sign paint and protec-
tive top coat: Acrylic Polyurethane w/ UV
inhibitor, nished with Clear Coat Satin nish.
Process Black
Pantone White
PMS 3435 C
PMS 337 C
P1 Black
P2 White
P3 Green
P4 Teal
Engineer-grade retro reective vinyl meeting
or exceeding FDOT requirements for day and
night draiving.
Background & Characters 3M custom inks
applied directly to 3930 with 3M approved
clear UV/Grati Vinyl Over-laminates.
Background & Characters 3M custom inks
applied directly to 3930 with 3M approved
clear UV/Grati Vinyl Over-laminates.
Background & Characters 3M custom inks
applied directly to 3930 with 3M approved
clear UV/Grati Vinyl Over-laminates.
3M Entineer Grade
Retro Reective
White
3M Scotchcal
3M Scotchcal
3M Scotchcal
V1 White Retro
Reective
V2 Emerald
Green
V3 Teal
V4 Black
City of Sebastian Destination Guide
City of Sebastian, FL 12DATE OF ISSUE
REVISION
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
06/28/2019
# Scale: NTS Pelican Path Map
N
Pelican PathsThe Greenways
and Blueways of
Sebastian, Florida
Sidewalk/Bicycling
Trail
Park
Waterway
Conservation Area
Canoe/Kayak/Boat Launch
Playground
ADA Playground
Walking/Running
Soccer
Picnic
Baseball
Dog Park
Football
Tennis
Volleyball
Basketball
Skateboarding
Pickleball
Bicycling
Swimming
Splash Pad
Rest Room
LEGEND
You are here
Bark Park
Easy St. Park
Friendship Park
Wimbrow Park
Riverview Park
Pickleball Complex
Garden Club Park
Storm Water Park Schumann Park
Bryant Ct. Park
Filbert ParkGeoge St. Park
Barber Street
Sports Complex
Blossom Park
Hardee Park
North County Conservation Park
North County Regional Park U.S
.
1U.S
.
1U.S
.
1
Kildare Dr.
Englar St.Schumann St.Barber St.66th Ave.Melton Ave.Filbert St.Friar St.Periwinkle Dr.Majestic Ave.Roulette St.Joyhaven Dr.Ra
n
c
h
R
d
.Sebastian CrossingWater VieletFellsmere Rails to Trails
Pelican PathsThe Greenways
and Blueways of
Sebastian, Florida
Co. Rd. 512
Co. Rd. 510Ind
ian
R
ive
r
D
r
.Main St.Co. Rd.
5
1
2
Easy St.Powerline Rd.Co. Rd. 512Co. Rd. 512Co. Rd. 512Wimbrow Dr.Roseland Rd.Barber St.Lake Dr.Blossom Dr.
Dolphin Ave.Roseland Rd.
SignPalette
City of Sebastian Destination Guide
City of Sebastian, FL 14Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Sign Palette - Gateways
Average eye level
for wheelchair users
2’
4’
6’
8’
10’
12’
14’
16’
18’
Working Waterfront Conceptual Design
Sebastian, FL Sign Design Palette for CRADRAWING NO.
SCALE: 1/2” = 1’DATE OF ISSUE
REVISION
01 of 01
04/22/2019
2
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gainconsultants.com/community solutions
City of Sebas�an Gateway Gateway with Marquee
4” FONT MESSAGE
NO LONGER
THAN 3 LINES
WELCOME TOWELCOME TO
FRIENDLY PEOPLE & SIX OLD GROUCHESFRIENDLY PEOPLE & SIX OLD GROUCHES
City of Sebastian Destination Guide
City of Sebastian, FL 15Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Sign Palette - Inside CRA
Parking Direc�onal Pedestrian Kiosk
Average eye level
for wheelchair users
2’
4’
6’
8’
10’
12’
14’
16’
18’
Gateway Large Vehicular Sign
For Roads >25mph
Small Vehicular Sign
For Roads <25mph
Working Waterfront Conceptual Design
Sebastian, FL Sign Design Palette for CRADRAWING NO.
SCALE: 1/2” = 1’DATE OF ISSUE
REVISION
01 of 01
04/22/2019
2
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gainconsultants.com/community solutions
CITY OF SEBASTIANDestination
Destination
Destination
Destination
Destination
Destination
Destination
Destination
Name
City Map
with 5 min
walk bubble
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
Destination
DestinationDestination
Destination
Destination
DestinationDestination
HOME OF THE PELICAN ISLAND
Routed letters and logo
Park Name
Park Address
PARK NAME
IN ALL CAPS
PARK NAME
IN ALL CAPS
1'-8"
6"
2'-8"
2'-0"
2'-3"
4'-10"
5'-9"
6'-5"
5'-3"4"
4'-7"
4'-7"
City of Sebastian Destination Guide
City of Sebastian, FL 16Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Sign Palette - Outside CRA
Parking Direc�onal
Average eye level
for wheelchair users
2’
4’
6’
8’
10’
12’
14’
16’
18’
Large Vehicular Sign
For Roads >25mph
Small Vehicular Sign
For Roads <25mph
Working Waterfront Conceptual Design
Sebastian, FL Sign Design Palette - Option CDRAWING NO.
SCALE: 1/2” = 1’DATE OF ISSUE
REVISION
01 of 01
04/22/2019
2
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gainconsultants.com/community solutions
CITY OF SEBASTIANDestination
Destination
Destination
Destination
Destination
Destination
Destination
Gateway
Destination
Name
HOME OF THE PELICAN ISLAND
Park Name
Park Address
PARK NAME
IN ALL CAPS
PARK NAME
IN ALL CAPS
4'-10"
5'-9"
1'-8"
2'-8"
4"
4'-7"
4'-7"
6"
6'-5"
5'-3"
City of Sebastian Destination Guide
City of Sebastian, FL 17Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Fisherman’s Landing Signs
Gateway
Average eye level
for wheelchair users
2’
4’
6’
8’
10’
12’
14’
16’
18’
Working Waterfront Conceptual Design
Sebastian, FL Sign Design Palette for CRADRAWING NO.
SCALE: 1/2” = 1’DATE OF ISSUE
REVISION
01 of 01
04/22/2019
2
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gainconsultants.com/community solutions
Routed letters and logo
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
was constructed with financial
assistance from the City of
Sebastian, Community
Redevelopment Agency and
Florida Inland Navigation District
(F.I.N.D.)
using the
acquired in 2018
Florida Communities Trust
Florida Forever Funds
Funds Acknowledgment Sign
Funding for the acquisition of
this site was provided by the
The Working Waterfront
Marina Project4'-0"
3'-0"4'-10"
5'-9"
Sign Details
City of Sebastian Destination Guide
City of Sebastian, FL 19DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings City of Sebastian Gateway
Front & Back View Side View
Wood grain painted on
green background
Painted black “drop shadow” - P1
100% opacity, 0 blur.
Stone gray wood grain
painted on pole
Scale 1/2in = 1ft
Elevation
Scale 1/2in = 1ft
Sign Face - Detail
WELCOME TOWELCOME TO
FRIENDLY PEOPLE & SIX OLD GROUCHESFRIENDLY PEOPLE & SIX OLD GROUCHES
WELCOME TOWELCOME TO
FRIENDLY PEOPLE & SIX OLD GROUCHESFRIENDLY PEOPLE & SIX OLD GROUCHES
P1
P2
P3
P4
V1
V2
V3
V4
P1
P1
P1
P2
P4
P3
P4
P4
P2
3"
3"
9"
3'-8"
3"
6"
5"
1'-3"
3"
2"
3"
3"
3"1'-2"4'-7"1'-2"3"
7'-4"
5'-7"
8'-8"
8'-6"
5"
1'-11"
3"
4'-9"
3"
3"
7'-10"
City of Sebastian Destination Guide
City of Sebastian, FL 20Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
City of Sebastian Gateway
Front SideScale 1/2in = 1ft
CITY OF SEBASTIAN GATEWAY SIGN:
Seven inch round aluminum poles
with wood grain painted background(1)
and single sided painted aluminum sign
cabinet with wood grain painted
background (2) painted with Matthews
automotive grade paint and UV inhabiter clear coat.
Sign face painted with screen quality masked and
painted copy and graphics (3). Direct burial in poured footer (4).
WELCOME TOWELCOME TO
FRIENDLY PEOPLE & SIX OLD GROUCHESFRIENDLY PEOPLE & SIX OLD GROUCHES
2
3
1
4
City of Sebastian Destination Guide
City of Sebastian, FL 21DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Gateway Sign
Front & Back View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
Painted black “drop shadow” - P1
100% opacity, 0 blur.
P1
P2
P3
P4
V1
V2
V3
V4
1'-5"
2'-6"
2'-11"
4'-1"
2"
1"
7"
8"
5"
3"
1"
5"
1 1/2"1 3/4"
1"
3'-0"
1'-1"
1"
4'-1"
4'-10"
5'-0"
Stone gray wood grain
painted on pole.
P2
P2
P1
P1
P1
P2
P2
P3
P4
P2
3"
1'-5"
2"
1'-0"
2"
2'-5"
2"2"
5'-9"
1'-8"
Wood grain painted on
green background
City of Sebastian Destination Guide
City of Sebastian, FL 22Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Gateway Sign
Front SideScale 1/2in = 1ft
PARK GATEWAY SIGN:
Five inch round aluminum poles
with wood grain painted background(1)
and double sided painted aluminum sign
cabinet with wood grain painted
background (2) painted with Matthews
automotive grade paint and UV inhabiter clear coat.
Sign face painted with screen quality masked and
painted copy (3). Direct burial in poured footer (4).
Foundation per City engineering requirements
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
2
3
3
1
4
City of Sebastian Destination Guide
City of Sebastian, FL 23Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Gateway with Marquee
Front View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
Scale 1in = 1ft
Marquee Side View Detail
4” FONT MESSAGE
NO LONGER
THAN 3 LINES
4” FONT MESSAGE
NO LONGER
THAN 3 LINES
Painted black “drop shadow” - P1
100% opacity, 0 blur.P1
P2
P3
P4
V1
V2
V3
V4
Stone gray wood grain
painted on pole
P2
P2
P1
P1
P1
P2
P3
P2
P1
P4
P2
Wood grain painted on
green background
2"2"
2'-10"
2"
1'-8"
2"
1'-5"
3"
7'-0"
3"
2'-11"
2"2"
1'-8"
2"
1'-5"
3"
1'-8"
6"6'-2 1/2"6"
2 1/2"
2"
6 1/2"
5 1/2"
1'-9 1/2"
2"
2"
2"
5 1/2"
5 1/2"
6"
1 1/2"
2"
2"1'-4 1/2"4'-7"2"
6'-3 1/2"
6"
City of Sebastian Destination Guide
City of Sebastian, FL 24Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Gateway with Marquee
Front SideScale 1/2in = 1ft
GATEWAY WITH MARQUEE SIGN:
Five inch round aluminum poles
with wood grain painted background(1)
and double sided painted aluminum sign
cabinet with wood grain painted
background (2) with custom welded angles to
create a message marquee (3), painted with Matthews
automotive grade paint and UV inhabiter clear coat.
Sign face painted with screen quality masked and
painted copy and graphics (4).
Foundation per City engineering requirements.
4” FONT MESSAGE
NO LONGERTHAN 3 LINES
2
3
1
4
City of Sebastian Destination Guide
City of Sebastian, FL 25DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Large Vehicular Directional Sign
Front & Back View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
CITY OF SEBASTIANDestination
Destination
Destination
CITY OF SEBASTIANDestination
Destination
Destination
Wood grain painted on
green background
P1
P2
P3
P4
V1
V2
V3
V4
Black outside CRA
Aluminum inside CRA
P1
P1
P1
V2
V4
V1
V1
P3
P2
P4
2'-8"
3'-1"
6'-2"
1'-1"
1'-5"
7"
R 5"
6"
4"
4"
6"
4"
1'-7"
1"
1'-0"
1"
1'-0"
1"
1'-0"
6'-10"
1'-2"
13'-10"
*
*
City of Sebastian Destination Guide
City of Sebastian, FL 26Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Large Vehicular Directional Sign
Front SideScale 1/2in = 1ft
LARGE VEHICULAR SIGN:
Six inch round aluminum pole (1) and
1/4 inch thick aluminum panels (2)
welded to custom bracket (3),
and applied directional discs mechanically
fastened to the panels (4). All painted with
Matthews automotive grade paint and
UV inhabiter clear coat.
Sign face painted backround color
and graphics with applied vinyl (5) copy
and logo. Decorative pole base (6).
Foundation per City engineering requirements.
CITY OF SEBASTIANDestination
Destination
Destination
2
3
1
6
3
4
City of Sebastian Destination Guide
City of Sebastian, FL 27DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Small Vehicular Directional Sign
Front & Back View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
Destination
Destination
Destination
Destination
Wood grain painted on
green background
Destination
Destination
Destination
Destination
P1
P2
P3
P4
V1
V2
V3
V4 Black outside CRA
Aluminum inside CRA
P1
P1
P1
V2
V4
V1
V1
P3
P2
P4
*
3"
1'-2"
3'-2"
6'-11"
1'-2"
8'-0"
2'-6"
4'-7"
1"
1'-2 1/2"
1/2"
1"
4"5"
R 3 1/2"
3"
3"
1'-8 1/2"
2'-2"
2'-6"
4'-7"
8"
3"
City of Sebastian Destination Guide
City of Sebastian, FL 28DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Small Vehicular Directional Sign
Front SideScale 1/2in = 1ft
SMALL VEHICULAR SIGN:
Four inch round aluminum pole (1) and
1/4 inch thick aluminum panels (2)
welded to custom bracket (3),
and applied directional discs mechanically
fastened to the panels (4). All painted with
Matthews automotive grade paint and
UV inhabiter clear coat.
Sign face painted backround color
and graphics with applied vinyl (5) copy
and logo. Decorative pole base (6).
Foundation per City engineering requirements.
Destination
Destination
Destination
Destination
2
3
1
6
3
4
City of Sebastian Destination Guide
City of Sebastian, FL 29DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Parking Directional Sign
Front View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
HOME OF THE PELICAN ISLAND
Destination
Name
HOME OF THE PELICAN ISLAND
Destination
Name
P1
P2
P3
P4
V1
V2
V3
V4
Black outside CRA
Aluminum inside CRA
P1
P1
P1
V2
V4
V1
V1
V2
V1
P4
P2
P1
P1
P2
*
3"
2'-8"
2"
7"
6'-1"
1'-2"
1"
2"
2'-1"
3"
1"
2'-8"
4"
5"
R 5"
1"
2 1/2"
2"
2 1/2"
4 1/2"
R 3 1/2"
City of Sebastian Destination Guide
City of Sebastian, FL 30DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Parking Directional Sign
Front SideScale 1/2in = 1ft
SMALL VEHICULAR SIGN:
Three inch round aluminum pole (1) and
boxed aluminum cabinet (2) welded to
custom bracket (3), painted with
Matthews automotive grade paint and
UV inhabiter clear coat.
Sign face painted backround color
and graphics with applied vinyl (4) copy
and logo. Decorative pole base (5).
Foundation per City engineering requirements.
HOME OF THE PELICAN ISLAND
Destination
Name
2
1
5
3
4
City of Sebastian Destination Guide
City of Sebastian, FL 31DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Pedestrian KioskScale: See Drawings
Front View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
DestinationDestination
Destination
Destination
DestinationDestination
Destination
City Map
with 5 min
walk bubble
Destination
Destination
Destination
Destination
Destination
Destination
Destination
P1
P2
P3
P4
V1
V2
V3
V4
Digital High Pressure
Laminate Map (Graphic)
Stone gray wood grain
painted on sign face
P1
P2
P1
P2
P2
P3
P2
P3
P4
P2
P2
1"
8"
1"
1'-3"
1"
4"
2'-0"
2'-0"
10"
1'-0"
1'-1"
2'-0"
7'-5"
4"
3"
1/2"
2"
5 1/2"
1"1/2"
2"
1/2"1"
1"
1"
1 1/2"
1'-0"
1'-1"
2'-0"
2'-3"
Wood grain painted on
green background
City of Sebastian Destination Guide
City of Sebastian, FL 32DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Pedestrian KioskScale: See Drawings
Front SideScale 1/2in = 1ft
PEDESTRIAN KIOSK:
Painted boxed aluminum (1) with
Matthews automotive grade paint and
UV inhabiter clear coat.
Double sided, non-illumonated,
sign cabinet with painted background
color, screen quality masked and painted
copy and graphics (2), and digital high
pressure laminate map (3). Foundation per
City engineering requirements.
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
Attractions Index
XX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction nameXX Attraction name 15 entries
Key
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry
Key entry 8 entries
Destination
Destination
DestinationDestination
Destination
Destination
Destination
City Map
with 5 min
walk bubble
2
1
3
City of Sebastian Destination Guide
City of Sebastian, FL 33Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Sign Maintenance and Longevity
Sign Longevity
Design and Planning
Vandalism
Cleaning Schedule
Management / Administration
Breakaway Product: Transpo
Reectivity Life Span:
3M High Intensity
Diamond Grade
Painted Surfaces
0-4 Years
Design: General Evaluation of positive and negative
aspects of the system. Planning: City In-house mainte-
nance based on new request and circulation/destination
updates.
Annual cleaning/repair. Stickers and grati are most
common. Cleaning solvents and Goo-Gone are typical
products utilized.
Annual Cleaning
Weekly coordination during initial installation, transi-
tioning to quarterly between City and fabricator during
year 1 and 2. On-going day-to-day monitoring of the
system, based on City and Sta observations.
Maintenance Free -Covered under Warranty for 3 years.
Covered under warranty for 5-7 years.
Covered under manufacturers warranty. General
maintenance and touch-up will be required.
5-9 Years
Design: General Evaluation of positive and negative aspects
of the system. Planning: Contract with a consultant to analyze
major changes to the City and necessary system adjustments.
1 or 2 updates possible during this time period.
Parts replacements and full sign replacement as needed.
Cleaning solvents and Goo-Gone are typical products utilized.
Annual Cleaning
Annual coordination between City and fabricator. Day-to-day
monitoring of the system, based on Facilities observations,
safety issues and citizens’ reports.
Maintenance Free - consider general review as part of yearly
inspection process.
Covered under warranty for 5-7 years. Reectivity may be
eective beyond the warranty period. Individual signs may
require sheeting to be replaced during this time period.
Warranty expires. Typically color holds up beyond warranty
period. Fading may begin depending on the direction sign
panel is facing. Individual signs may require individual parts
to be replaced during this time period.
10-15+ Years
If the system has not been analyzed since implementation, a
major updating is likely to be needed. City planner or
consultants will be required to review and inventory the
system, as well as make suggested changes based on new
circulation, destinations, etc.
Parts replacements / full sign replacement as needed. Clean-
ing solvents and Goo-Gone are typical products utilized.
Annual Cleaning
Annual coordination between City and fabricator.
Day-to-day monitoring of the system, based on Facilities
observations, safety issues and citizens’ reports.
Maintenance Free - consider general review as part of yearly
inspection process.
Reectivity becomes less eective, if not previously
replaced. 10 – 15 years is the maximum lifespan.
Fading occurs – based on direction sign panel is facing. 10 –
15 years is the maximum lifespan to expect.
City of Sebastian Destination Guide
City of Sebastian, FL 34DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Construction Details
CONSTRUCTION DETAILS
Modular detail of system of changable panel signs.
These drawings are meant for DESIGN
INTENT ONLY and are not for construction.
Contractor shall verify and be responsible
for all dimensions and conditions
of the job. Contractor shall be familiar
with the site and conditions it presents.
This oce must be notied of any variations
from the dimensions and conditions
shown on this drawing. Shop drawings
and details must be submitted to this
oce for approval prior to proceeding with
fabrication. All copy shall be proofread by
client and legal requirements checked by
legal department.
-
-
-
Section Detail
scale: 3"=1'-0"
Exploded view
n t s
3
5
7
4
1
4
5
3
1
2
6
1
2
3
4
5
6
7
Custom aluminum extrusion bracket plug welded to pole cu
Alum message panel mechanically fastened to bracket
Aluminum pole
Brake-formed alum pole cu
Stainless steel through-bolt
Set screws
Post-cap assembly
City of Sebastian Destination Guide
City of Sebastian, FL 35DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Construction Details
CONSTRUCTION DETAILS
Detail of Frangible breakaway footer details
These drawings are meant for DESIGN
INTENT ONLY and are not for construction.
PERFORMANCE CRITERIA:
1. Double-Neck Pole-Safe meets
all requirements of "AASHTO
Standard Specications for
Structural Supports for
Highway Signs, Luminaries,
and Trac Signals."
2. Double-Neck Pole-Safe has
been crash-tested and FHWA
approved in accordance with
the requirements of NCHRP
Report 350, "Recommended
Procedures for the Safety
Performance Evaluation of
Highway Features."
3. Maximum Allowable Pole
Mass = 450 kg (922 lb) (total
including xtures).
PHYSICAL PROPERTIES PER
COUPLING:
1. Ultimate Tensile Strength =
221.5 kN (49.8 kips), minimum
2. Tensile Yield Strength = 192.0
kN (43.2 kips), minimum.
3. Ultimate Restrained Shear
Strength = 24.5 kN (5.5 kips),
maximum
CORROSION PROTECTION:
All Hardware items are American
Standard sizes, galvanized in
accordance with ASTM A153
(hot dipped).
Source: Transpo Industries, Inc.
-
-
-
Transpo ® Type C Female Anchor
for use with Pole -Safe ® Model No. 5075
Breakaway Support System for Light Poles
20 Jones Street
New Rochelle, NY 10801
914 -636 -1000
Transpo ® Type C Female Anchor
(Typical, 4 per Pole)
3/00
Bolt Circle Diameter
Top Surface of
Concrete Foundation
Template
(temporary)
Transpo ® Type C Female Anchor
(Typical, 4 per Foundation)
Foundation Form or oth er means
of support for template while
concrete cures
Template Bolt
(temporary)
See other side of page for complete
Installation Instructions
Typical Anchor Layout
381 mm
(15”)
Top of Concrete
Foundation
Stainless Steel W asher
64 mm (2 -1/2”) O.D.
20.6 mm (13/16”) I.D.
3.2 mm (1/8”) Thick
Stainless Steel
Threaded Ferrule
3/4”-10 UNC (19 mm)
Thread Depth = 29 mm
(1 -1/8”), minimum
Steel Wire, 11.1 mm
(7/16”) Diameter
(4 per Anchor)
56 mm (2 -3/16”)
Closed Wire Coi l
37 mm (1 -7/16”) O.D.
51 mm (2”) Long
6 Revolutions
3/00
SPECIFICATIONS
Physical Properties:
1.Ultimate Tensile Load = 266.9 kN (60.0 kips)
minimum per Anchor.
2.Actual Pullout Strength depends on foundation
design and concrete properties.
Installation Instructions:
See other side of page for typical installation diagrams.
1.Fabricate a t steel or wood template with four (4) 19
mm (3/4”) diameter holes located to match the
specied bolt pattern of the pole base plate.
2.Attach four (4) Pole -Safe ® Type C Female Anchors
to template using four (4) 19 mm (3/4”) diameter
bolts. Ensure that each Anchor Washer is u sh and
snug against the bottom of the templa te .
3.Lower Anchor Assembly into fresh concrete
foundation, and vibrate into position such that the
tops of the Anchor Washers are ush with the
nished top surface of the foundation.
4.Support template such that all Anchors are level and
in their proper loc ations.
5.Allow concrete to cure, and then remove bolts and
template from the top of the foundation.
Transpo® Type C Female Anchor
for use with Pole -Safe ® Model No. 5075
Breakaway Support System for Light Poles
20 Jones Street
New Rochelle, NY 10801
914 -636 -1000
41 mm
(1 -5/8”)
Plan: Footer Placement
SCALE: NTS
NOTE: When locating a footer within a single pavement block
(max. 5’-0” x 5’-0”), adjacent to at least 2 expansion joints, the
entire block of pavement shall be removed and replaced with
the same materials and n ish of adjacent sidewalk areas.
Footer
Sign Post
Existing sidewalk block
to be removed and replaced
Plan: Footer Placement
SCALE: NTS1
Plan V iew: Footer
SCALE: 1" = 1' - 0"
NOTE: When locating a footer within a single pavement block
(max. 5’-0” x 5’-0”), adjacent to at least 2 expansion joints, the
entire block of pavement shall be removed and replaced with
the same materials and n ish of adjacent sidewalk areas.3'-0"3'-0"
Footer
Class B Concrete Footing
Sign Post Base
Sign Post
Sign Post
Existing sidewalk block
to be removed and replaced
CL
CL
City of Sebastian Destination Guide
City of Sebastian, FL 36DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Construction Details
CONSTRUCTION DETAILS
Detail of Frangible breakaway footer details
These drawings are meant for DESIGN
INTENT ONLY and are not for construction.
Contractor shall verify and be responsible
for all dimensions and conditions
of the job. Contractor shall be familiar
with the site and conditions it presents.
This oce must be notied of any variations
from the dimensions and conditions
shown on this drawing. Shop drawings
and details must be submitted to this
oce for approval prior to proceeding with
fabrication. All copy shall be proofread by
client and legal requirements checked by
legal department.
-
-
-
Section V iew: Foundation @ Concrete
Pole Height - 10 to 20 ft.
SCALE: 3/4" = 1'-0"1
Section V iew: Foundation @ Concrete
Pole Height - Less than 10 ft.
SCALE: 3/4" = 1'-0"2
1'-6" Dia.5'-0"5" Sidewalks
7” Driveways
1'-6" Dia.3'-0"5" Sidewalks
7” Driveways
Existing
concrete slab
Break-A way
sign support
Base Plate welded
to sign post.
Pole HEIGHT greater
than 10 feet, and less
than 20 feet.
2 ties @
3” O.C. at top
of footing
6- #6 vert
w/ #3 ties @
12” O.C.
Note: Design Wind load
300 PSF 100 MPH,
3 Sec Gust Wind, Exp C
Existing
concrete slab
Break-A way
sign support
Base Plate welded
to sign post.
Pole HEIGHT less
than 10 feet.
2 ties @
3” O.C. at top
of footing
6- #6 vert
w/ #3 ties @
12” O.C.
Note: Design Wind load
300 PSF 100 MPH,
3 Sec Gust Wind, Exp C
Section V iew: Foundation @ Pavers
Pole Height - 10 to 20 ft.
SCALE: 3/4" = 1'-0"3
Section V iew: Foundation @ Pavers
Pole Height - Less than 10 ft.
SCALE: 3/4" = 1'-0"4
1'-6" Dia.5'-0"5" Typ.
Sidewalks
5" Typ.
Sidewalks
1'-6" Dia.3'-0"Brick Pavers
Break-A way
sign support
Base Plate welded
to sign post.
Pole HEIGHT greater
than 10 feet, and less
than 20 feet.
2 ties @
3” O.C. at top
of footing
6- #6 vert
w/ #3 ties @
12” O.C.
Note: Design Wind load
300 PSF 100 MPH,
3 Sec Gust Wind, Exp C
Brick Pavers
Break-A way
sign support
Base Plate welded
to sign post.
Pole HEIGHT less
than 10 feet.
2 ties @
3” O.C. at top
of footing
6- #6 vert
w/ #3 ties @
12” O.C.
Note: Design Wind load
300 PSF 100 MPH,
3 Sec Gust Wind, Exp C
Fisherman’s Landing Sign Details
City of Sebastian Destination Guide
City of Sebastian, FL 38DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: See Drawings Gateway Sign
Front & Back View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
Painted black “drop shadow” - P1
100% opacity, 0 blur.
P1
P2
P3
P4
V1
V2
V3
V4
1'-5"
2'-6"
2'-11"
4'-1"
2"
1"
7"
8"
5"
3"
1"
5"
1 1/2"1 3/4"
1"
3'-0"
1'-1"
1"
4'-1"
4'-10"
5'-0"
Stone gray wood grain
painted on pole.
P2
P2
P1
P1
P1
P2
P2
P3
P4
P2
3"
1'-5"
2"
1'-0"
2"
2'-5"
2"2"
5'-9"
1'-8"
Wood grain painted on
green background
City of Sebastian Destination Guide
City of Sebastian, FL 39Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Gateway Sign
Front SideScale 1/2in = 1ft
PARK GATEWAY SIGN:
Five inch round aluminum poles
with wood grain painted background(1)
and double sided painted aluminum sign
cabinet with wood grain painted
background (2) painted with Matthews
automotive grade paint and UV inhabiter clear coat.
Sign face painted with screen quality masked and
painted copy (3). Direct burial in poured footer (4).
Foundation per City engineering requirements
STAN MAYFIELD WORKING WATERFRONT
1540 Indian River Drive Sebastian, FL 32958
2
3
3
1
4
City of Sebastian Destination Guide
City of Sebastian, FL 40Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Fund Acknowledgment Sign
Front View Side ViewScale 1/2in = 1ft
Elevation
Scale 1in = 1ft
Sign Face
was constructed with financial
assistance from the City of
Sebastian, Community
Redevelopment Agency and
Florida Inland Navigation District
(F.I.N.D.)
using the
acquired in 2018
Florida Communities Trust
Florida Forever Funds
Funding for the acquisition of
this site was provided by the
The Working Waterfront
Marina Project
was constructed with financial
assistance from the City of
Sebastian, Community
Redevelopment Agency and
Florida Inland Navigation District
(F.I.N.D.)
using the
acquired in 2018
Florida Communities Trust
Florida Forever Funds
Funding for the acquisition of
this site was provided by the
The Working Waterfront
Marina Project
P1
P2
P3
P4
V1
V2
V3
V4
P1
P1
P1
P2
P1
P2
P3
P1
P2
5'-1"
5'-3"
1"
4'-0"
1"
1'-7"
1'-0"1'-1"11"1"5"1'-2"5"
3'-0"2'-0"
2"
1'-7"
2"
3"
3"
2"
1 1/2"
3/4"
4 1/2"
1'-3"
4"
2"
1 1/2"
2"
1 1/2"
1 1/2"
City of Sebastian Destination Guide
City of Sebastian, FL 41Scale: 1/2” = 1’DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Fund Acknowledgment Sign
Front SideScale 1/2in = 1ft
FUNDS ACKNOLEDGEMENT SIGN:
Three inch round aluminum poles (1)
and single sided painted aluminum sign
cabinet (2) painted with Matthews automotive
grade paint and UV inhabiter clear coat.
Sign face painted with screen quality masked and
painted copy (3) mounted with a custom aluminum
bracket (4) to poles.
Foundation per City engineering requirements.
was constructed with financial
assistance from the City of
Sebastian, Community
Redevelopment Agency and
Florida Inland Navigation District
(F.I.N.D.)
using the
acquired in 2018
Florida Communities Trust
Florida Forever Funds
Funding for the acquisition of
this site was provided by the
The Working Waterfront
Marina Project
5
2
3 4
1
Sign PlacementRecommendations
City of Sebastian Destination Guide
City of Sebastian, FL 43DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: NTS Vehicular Recommendations
24”Direction of viewerDistance from curb to
sidewalk on 192
(13th Street)
Vehicular Directional Vehicular Directional with Turn Lane
Direction of viewer
City of Sebastian Destination Guide
City of Sebastian, FL 44DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: NTS Park Gateway Recommendations18 inMin.Gateways for parks with no parking lots Gateways for parks with parking lots
MARKED OR
UNMARKED
CROSSWALK
SIDE WALK
4 ft Min.
6 ft Min.
Parking Lot
2 ft
Min.
3 ft Min.
City of Sebastian Destination Guide
City of Sebastian, FL 45DATE OF ISSUE
REVISION
08/16/2019
#
A GAI Consultants, Inc. Service Group
618 E. South Street Suite 700Orlando, Florida 32801T 407.423.8398gaiconsultants.com/community solutions
Scale: NTS Pedestrian Signs Recommendations
2 ft
Min.
Urban Intersection
MARKED OR
UNMARKED
CROSSWALK
SIDE WALK
4 ft Min.4 ft Min.
6 ft Min.6 ft Min.
Pedestrian Corridor Pedestrian Corridor 3'-0" Min.
2'-0" Min.
Contact
Peter C. Sechler, PLA, AICP
Senior Director
Community Solutions Group
T (321) 319.3126
P.Sechler@gaiconsultants.com
Kristin Caborn CPRE, FCP
Senior Planning Manager
Community Solutions Group
T (321) 319.3161
K.Caborn@gaiconsultants.com
Ana Oropeza Degwitz
Senior Environmental Designer
Community Solutions Group
T (321) 319.3075
a.oropezadegwitz@gaiconsultants.com
Revised: September 23, 2019 gaiconsultants.com/communitysolutions